Archive

Posts Tagged ‘Wabco’

Commercial Repairs For Trailer Faults

October 12th, 2019 No comments

With the growing need for fault finding the modern way, Code Talk Trailer Diagnostics is becoming more and more of interest to the commercial vehicle trade.

Cooks Commercials, based in Taunton consulted aide automotive of the available tools to determine faults on trailers, reviewing TrailerCheck, The EBS ABS Sensor Master & Code Talk it became obvious the full trailer diagnostic system Code Talk was the correct tool.

Code Talk is a world-renowned Diagnostics Handheld Fault Code Reader for all Trailer Manufacturers including WABCO, HALDEX, KNORR-BREMSE and specifically their trailer ABS/EBS Brake systems. This product is used by being plugged into the braking ECU and will read out and clear any fault codes that the trailer may have. The Code Talk can also show live air pressures, wheel speeds, and system voltages which also helps with the diagnostics on the trailer. It can also act as a remote to our VTC allowing you to work from inside an HGV Service Van.

With NO annual software fee with Code Talk, this trailer diagnostics tool is by far the best on the UK market. Up gradable for future proofing, the Code Talk will outlast and beat any Texa or JalTest system.

Code Talk Trailer Diagnostics is an aftermarket engineers’ diagnostic tool, designed by UK trailer maintenance engineers for engineers.

Contact aide automotive on 0115 8456471 To Discuss Trailer Diagnostics for a Haulage Trailer Fleet

 

24 Volt CV Diagnostics

Code Talk is the next generation of trailer diagnostics from aide automotive ltd.

Commercial Vehicle Caliper Tester

September 24th, 2019 Comments off

HGV Brake Caliper Tester

The tester is used to check the potentiometers (wear indicators) in brake calipers and for the determination of the wear of the brake disc and brake pads.

The practice of checking a potentiometer for faults and replacement could save a commercial vehicle operator thousands instead of complete caliper replacements!!

The reported practise of replacing a complete calipers rather than testing and replacing a potentiometer is in the past if you own an aide automotive Potentiometer Tester.

The procedure for checking the potentiometer can be carried out with the caliper installed on the vehicle or with the caliper removed, simply connect the supplied correct cable to the brake potentiometer, power the tester and choose which type you are testing, MAN / Mercedes 3 Wire Gold DAF / Mercedes 2 Wire Scania / Iveco /
Mercedes 3 Wire Silver

The display will show the voltage, pad wear percentage & bar graph.

To set a new potentiometer simply wind the potentiometer until the display show 0 %, done!!

To test a potentiometer, wind the potentiometer until about 2.75 volts, this will show low pads warning and then to 100% for failure warning. SIMPLE!!

So start testing & replacing potentiometers to save money today!!
Buy Online Here HGV Caliper Tester

HGV Caliper Tester

Truck Potentiometer Tester For Brake Calipers

DVSA Suggests More HGV Brake Tests ??

September 11th, 2019 Comments off

aide automotive explains why its portable Bowmonk BrakeCheck solution is a viable alternative to roller brake testers when carrying out a non-MOT brake test.
Regular brake tests are currently being requested by the DVSA on all commercial vehicles of 7.5 tonne and over, as part of an interim safety inspection. At the absolute minimum, the agency is asking for a quarterly voluntary brake test to be carried out in addition to the annual MOT test.

Fortunately, most commercial operators have taken heed of this request and are having their brakes checked more frequently, as it is a means of monitoring braking efficiency more closely. However, in some cases, it would appear that this frequency of testing is still not enough, as the level of deterioration is a cause for concern.

In most cases, the DVSA would prefer this test to be carried out as part of the six-weekly inspection. This would have thebenefit of highlighting a decrease in braking performance considerably sooner than those performed once every three months, and in doing so, afford more effective preventative maintenance opportunities.

Evidently, there are a great number of commercial workshops who are still of the misconception that all of the aforementioned brake tests have to be performed on a roller brake tester. This is not the case! The Traffic Commission has allowed the use of a DVSA-approved brake tester, like Bowmonk’s BrakeCheck, for all non-MOT brake tests.

Aside from the mandatory requirements, there is also the upsell opportunity. Workshops providing a brake overhaul service, where components are in need of replacement, can offer a ‘before and after’ brake test report; an opportunity to show their customers the level of efficiency achieved prior to and following any necessary repair work.

A user guide to BrakeCheck

Position the BrakeCheck unit on a level surface, such as the passenger side foot well. Switch the unit on by pressing and holding the ‘Menu’ button until ‘Sbr’ appears in the display.
Confirm Service Brake choice by pressing ‘Enter’.
When the unit is level enough to start the test, a symbol (pictured left) will be shown on the display. Once the symbol is displayed, press ‘Enter’.
The unit is now ready for the test. When the test area is clear, accelerate the vehicle to an appropriate test speed (e.g. 20 mph).
Once the vehicle is travelling at an appropriate test speed, check for traffic approaching from behind. If safe to do so, apply the footbrake as a controlled emergency stop, without skidding.
Once the vehicle has been brought to a complete stop, the unit will generate and display a braking efficiency value.
Once the Service Brake test is complete, change to Hand Brake mode by pressing the ‘Menu’ button (so that the hand brake test LED is illuminated). As before, confirm this choice by pressing ‘Enter’, which will take you to the levelling display. Press ‘Enter’ when the level indicator is shown.
As before, accelerate the vehicle to the test speed, this time applying the hand brake to stop the vehicle. Note: please check with your vehicle manufacturer if this type of procedure is acceptable.
Once the vehicle has come to a complete stop, the display will show the braking efficiency of the hand brake.
To view the service brake test report, press the ‘Menu’ button until the last test result and service brake test LEDs are illuminated. Then press ‘Enter’ to display the result, which can now be printed using the optional wireless printer.
With the BrakeCheck unit positioned approximately 2 to 3cm in front of the infra-red printer, switch on the printer and press the ‘Print’ button on the BrakeCheck to print the test result.
To view or print the hand brake test, carry out the same procedure, but use the ‘Menu’ button to illuminate the hand brake test and last test result LEDs.

Buy Online Bowmonk BrakeCheck Decelerometer

HGV Brake Tester

Buy Online Bowmonk BrakeCheck Decelerometer

Fresnel Lens / Truck Anti Siphon / Sender Unit Safe / Sensor Master Purchase Online

August 26th, 2019 Comments off

It’s Bank Holiday At #aideauto But You Can Still Purchase Any Of Our Top Sellers! #fresnel #lens #Truck #Anti #Siphon #SenderSafe #Sensor #Master. Visit the aide automotive Shop To Buy Or @ #eBay Have A Great BH!

Truck Fresnel Lens PVC
The Fresnel Lens is a clear, thin, flat plastic lens that is press fitted to a truck’s passenger door window.

Due to a blind spot, drivers of trucks cannot see smaller vehicles or other vulnerable road users which are immediately next to the passenger side door of their HGV. These unseen road users can be hit if the truck changes lane in their direction.

Truck Fuel Tank Sender Protection
Sender Safe is a new product to help with fuel security around a Truck Diesel Fuel Tank.

Sender Safe is a robust and easy to fit protective shield for a Truck Fuel Tank Sender unit, increased protection of the fuel tank filler entry by fitting anti siphon devices has meant the Sender Unit is now the way to steal fuel.

The Sender Safe unit sits on top of the fuel tank attached by the fuel tank mounting straps, Sender Safe prevents access and damage to the Fuel Tank Sender Unit.

TP UltraPlus – Anti Fuel Theft Device
TP UltraPlus is a high quality Truck Anti Fuel Theft device that helps to prevent the Fuel Theft from commercial vehicles.

This device is simple to fit, taking no more than a few minutes, with no drilling or gluing to a fuel tank.

TP UltraPlus can be fitted to all types of tank: bayonet, screw type & bus /coach.

Truck Manufacturers include, Volvo, MAN, DAF, Iveco, Scania, Renault, Foden, Hino & Mercedes

EBS ABS Sensor Tester
The EBS ABS Sensor Tester is one of aide automotive’s best selling products.

Any workshop requires fast, accurate and effective tools to diagnose faults easily and quickly. A high percentage of brake EBS/ABS faults are around the sensor or the sensor itself.

#diesel #automotive #repairs #hgv #theft #abs #transport #servicing #diagnostics #stolen

Contact aide automotive on 0115 8456471 or email shoponline@aideautomotive.com

 

Our Top Sellers! #fresnel #lens #Truck #Anti #Siphon

Purchase Online Fresnel Lens / Truck Anti Siphon / Sender Unit Safe / Sensor Master

Re Calibration BrakeCheck MOT Bowmonk

August 8th, 2019 Comments off

If you require your Bowmonk BrakeCheck to be recalibrated or if its in need of repair, please follow the information below:

 

If you require your Bowmonk BrakeCheck to be tested for calibration, please see below instructions & relating charges for the calibration check.

With all tools in your workshop, you need to know they are working correctly and in test situations supplying the correct information. With this, we advise that your BrakeCheck is recalibrated.

We will aim to complete the recalibration of your BrakeCheck within 48-72 hours of receipt of the unit.

Option 1 – BrakeCheck Recalibration (ONLY)

Price
BrakeCheck Re calibration – £82.00 per unit
Carriage Options – £6.45 per unit by Signed for Royal Mail Or £9.95 by next day courier. (Not including Ireland)
Also:
New Batteries Are Recommended Every 4-6 Years, if required – £55.00
Need Any Paper For the Printer ? – Box of Paper Rolls – £30.00 If ordered the return carriage would be £14.50

For BrakeCheck recalibration (ONLY), you will need to return the BrakeCheck only. Please note chargers, cases, printers are not required.
It is suggested that you use a royal mail recorded delivery service / special delivery or courier to ensure that the unit(s) reach us safely.

Returns address: –
aide automotive Limited
Service Dept
Foxhall Business Centre
Foxhall Road
Nottingham, NG7 6LH

Option 2 – BrakeCheck recalibration with Service and test

Price
BrakeCheck Recalibration – £82.00 per unit
If your Kit is Older Than 4 years, You May Require & Service & Test – £55.00
Service & Test Checks All Items As preventive Maintenance & Cleaned To A Best Possible Standard

If you have lost or found to be faulty, you may require:
New BrakeCheck Or Printer Charger – £24.95
New BrakeCheck Batteries Are Recommended Every 4-6 Years, if required – £55.00
New Printer Batteries Are Recommended Every 4-6 Years, if required – £14.50
Box of Paper Rolls – £30.00
Return Next Day Courier – £14.50

All prices exclude VAT.

For BrakeCheck recalibration, service & test, you will need to return your BrakeCheck, Case, Printer & Accessories such as Chargers.
It is suggested that you use a royal mail special delivery service or signed for courier to ensure that the unit(s) reach us safely

Returns address: –
aide automotive Limited
Service Dept
Foxhall Business Centre
Foxhall Road
Nottingham, NG7 6LH

Please be so kind as to provide a full postal address so that we can return your tester efficiently!

Payment, once the required work is completed, our accounts dept will email a proforma invoice with options of online payments, card / PayPal / BACS.

If you would like to book your Bowmonk BrakeCheck in, please replay to this email.

If you have any questions, please feel free to call the office on 0115 845 6471

Prices are correct as 08.08.19, for latest prices please confirm before returning your Bowmonk BrakeCheck to us.

 

BrakeCheck Bowmonk Calibration

Bowmonk MOT Calibration Check

Truck EBS Brake Tester

July 31st, 2019 No comments

This Is The ISOCheck EBS Plus Tool.

Designed By Our In House Tech Team The ISOCheck Tool Will Test The ISO7638 Socket On The Rear Of A Tractor Unit.

Trucks first used on the road on or after 1 May 2002 must be fitted with ISO 7638 connections. If a truck is fitted with an Electronic Braking System (EBS) and is towing a trailer fitted with EBS then a 7 core cable must be used. Trucks & Trailers with a defective EBS system (especially double decker trailers) would vastly increase the chances of roll over or jack-knife.

The simple & quick procedure of attaching the tester to the ISO7638 Truck Susie Socket and turning on the ignition will confirm Green for Good Or Red for Fault! So when the truck is returned to the road all information from the trucks ISO7638 can be trusted & proven.

Also, if the RED light indicates a fault, ISOCheck EBS-Plus will indicate which pin is at fault. Once the initial power test is complete with a RED fault light, ISOCheck will then go into diagnostic mode and flash a 1 to 7 count sequence in relation to the faulty pin.

ISOCheck EBS will test all electronic braking systems, Wabco, Knorr Bremse and Haldex, covering the differences between the early generations and the latest.

So for truck manufacturer workshops to large haulage fleets to small independent commercial repairers, ISOCheck Is An Ideal Tool!

Inspection Sheet Check Of The ISO Brake Line Creates A Safety Brake Check.

aide automotive 0n 0115 8456471

The Electronic Braking System (EBS) Susie or the ISO 7638

What Is The ISO EBS Truck & Trailer Lead?

ISO7638 Truck & Trailer Tester

July 19th, 2019 Comments off

#Commercial #Vehicle Workshop is a business magazine for companies and individuals involved in all aspects of commercial vehicle servicing.

#Trailer #Servicing & fault finding was featured in the recent July issue with an advert from aide automotive detailing the #ISOCheck.

ISOCheck EBS will test all electronic braking systems, #Wabco, Knorr #Bremse and #Haldex, covering the differences between the early generations and the latest.

ISOCheck really becomes the perfect test tool on a dark wet night, the quick test and the bright (Green) OK / Fault (Red) answer increases test and repair efficiency.

ISOCheck can be used as a constant visual aide on any truck and trailer but possibly especially for double decker trailers. Double decker trailers with a defective EBS system would vastly increase the chances of roll over or jack-knife. With ISOCheck in place a driver or depot gateman would be able to see the RED warning light.

To read the full article on Trailer Servicing, go to the CVW Magazine website to review an online copy.

Contact aide automotive on 0115 8456471 to learn more about #ISO7638 testing for truck & trailer.

 

#Commercial #Vehicle Workshop is a business magazine for companies

ISOCheck EBS will test all electronic braking systems, #Wabco, Knorr #Bremse and #Haldex

Truck Potentiometer Tester For Brake Calipers

June 25th, 2019 Comments off

Commercial Vehicle Brake Caliper Tester

The tester is used to check the potentiometers (wear indicators) in brake calipers and for the determination of the wear of the brake disc and brake pads.

The practice of checking a potentiometer for faults and replacement could save a commercial vehicle operator thousands instead of complete caliper replacements!!

The reported practise of replacing a complete calipers rather than testing and replacing a potentiometer is in the past if you own an aide automotive Potentiometer Tester.

The procedure for checking the potentiometer can be carried out with the caliper installed on the vehicle or with the caliper removed, simply connect the supplied correct cable to the brake potentiometer, power the tester and choose which type you are testing, MAN / Mercedes 3 Wire Gold DAF / Mercedes 2 Wire Scania / Iveco / Mercedes 3 Wire Silver

The display will show the voltage, pad wear percentage & bar graph.

To set a new potentiometer simply wind the potentiometer until the display show 0 %, done!!

To test a potentiometer, wind the potentiometer until about 2.75 volts, this will show low pads warning and then to 100% for failure warning. SIMPLE!!

So start testing & replacing potentiometers to save money today!!

Visit the aide automotive Ltd website for more information on Commercial Vehicle Brake Caliper Tester

 

HGV Caliper Tester

Truck Potentiometer Tester For Brake Calipers

Do You Know What Brake Testing You Should Be Doing?

June 19th, 2019 Comments off
Since April 2014 the DVSA have been recommending commercial vehicles undertake 4 brake tests per year!

This is a recommendation based on the DVSA’s guidance paper.

So as this is a recommendation, what is the law? Is the law is one RBT as a MOT per year?

Well it is if the DVSA is a guidance paper, or is it?

If the guidance set out by the DVSA isn’t followed and the operator is inspected by the DVSA or addressed by a traffic commissioner. The guidance set out by the DVSA is used as the standard an operator should meet, does this now make it law?
Well the operator has to make this call; do you follow the guidance or not? Keeping a fleet roadworthy and safe must be a high priority for any management team, after all the with laws around corporate manslaughter all risks need to be seriously considered.
Many operators have moved with the guidance but still 5 years has passed with some commercial vehicle operators still unaware of the law and guidance.

So, regarding commercial vehicle brake testing, the guidance states:

Document :Guide to maintaining road worthiness
Commercial goods and passenger carrying vehicles (Revised 2014)

Section 5: Safety inspection and repair facilities

Extract –
“Therefore, it is normally expected that the vehicle or trailer should complete at least three successful brake efficiency tests spread throughout year in addition to the annual MOT test.”

An operator can take the decision to carry out brake tests using roller brake tests or a decelerometer.

As the consequences of non-compliance with the required standards can be very severe and include prohibition, fines or prosecution, operators are advised to ensure that they are familiar with all the changes within the DVSA guidance.

Following The Bath Tipper Incident Inquiry, HGV Brake Testing is Essential!!

The inquiry showed the Bath tipper truck to have been poorly maintained which resulted when tested to have a very poor brake efficiency.
aide automotive recommend the use of roller brake testers and decelerometers within a 12-month maintenance and testing policy.

Also, the use of an Infra-Red Temperature Gun, Infra-Red Temperature guns are an excellent way of individual brake testing of wheel disks or drums to determine brake activation. With the ease of just pointing the Infra-Red Light at the wheel hub from the outer edge of a trailer or truck and without removing wheels, an infra-Red Temp Gun can indicate if a wheel is not braking efficiently as compared to the other wheels on the vehicle.

aide automotive market a range of Brake Testing, Servicing & Diagnostic Tools for commercial vehicle workshops.

With the Bowmonk BrakeCheck Portable Decelerometer Printer kit, a workshop can meet the 3 additional required brake tests with minimum fuss. For Trailer Servicing & Diagnostics, aide offer a complete Trailer Electrical (ABS Light & EBS CAN Line Test), Light and Air Brake Tester with Diagnostics interface for Trailer ECU Code Reading / Clearing and management data viewing. EBS/ABS Sensor Master testing can be conducted with the Sensor Master, while Battery Diagnostics Tests with a Midtronics MDX Battery Tester.
aide automotive offer a range of products to help with DVSA Guide To Roadworthiness. Contact us via our website www.aideautomotive.com
HGV DVSA Truck Brake Tester

 

Brake Tester, Diagnostics, Battery Testers

aide auto Market Truck & Trailer Workshop Test Tools

Agricultural tractor Brake Test would meet the road worthines

March 2nd, 2018 Comments off

Tractors To Require An O Licence

Agricultural tractors “likely” to require an O-licence

aide automotive have recently seen media reports of agricultural vehicles possibly being made to meet better road safety regulations as per commercial vehicles on UK roads.
Commercial Motor published:
Agricultural tractors that carry out commercial haulage will be subject to roadworthiness testing requirements from next year – and are likely to fall under the O-licensing regime.
From 20 May 2018, operators of agricultural tractors capable of travelling more than 40km/h (approximately 25mph), used to carry commercial goods, will be required to undergo a roadworthiness test four years after their registration and every two years thereafter.
In its response to a consultation carried out last year, the DfT also noted that operators of such tractors would likely require an O-licence.
However, the RHA said the changes did not go far enough to address the concerns about competition, and said allowing tractors to carry freight will encourage more to be used for haulage.
“Ideally we would like to see these vehicles banned from moving freight on public roads entirely as their design is not equivalent to well-designed lorries for that task,” said policy director Duncan Buchanan.
“We do not believe that the frequency, four years for the first test then every two years, is justified. It looks very odd for heavy vehicles like these to be tested so infrequently when a 50cc moped is required to be tested every year after three years.”
The FTA’s head of policy and compliance information, James Firth, added: “If it looks like a truck or it’s doing the work of a truck, test it like a truck. Members in areas where agriculture is a primary economy have long raised concerns that agricultural tractor units, and specially developed fast tractors, were competing in the haulage market without being burdened by the same safety standards.”
On the subject of O-licensing, Buchanan added: “If it is the case then operators would need to obtain O-licences from when the vehicle was new. They should also have to comply with the same level of rigour as lorries.”
Vernon Hill, director at Kings Lynn-based Vernon Hill Agricultural Services, supported bringing tractors into the O-licensing regime.
He said: “An agricultural contractor friend of mine who runs lorries and tractors thinks the cost of each is very similar, so if farmers think they are saving money by not using a haulier they may be kidding themselves.
“If they are doing commercial haulage, why shouldn’t they be in scope of O-licensing?”
The weight and speed limits for farm tractors and trailers on UK roads increased in 2015. Tractors are not currently subject to mandatory testing.
If tractors are to fall under the O licence criteria, agricultural workshops and repair engineers will have to look at regular brake testing, one way to test tractor brakes is the BrakeCheck decelerometer.
Easy to use and with hard copy print options, brake testing a agricultural tractor with a BrakeCheck would meet the road worthiness requirement of an O licence.
Contact aide automotive on 0115 8456471 for BrakeCheck pricing and any further information that me be required.
Brake Tester For Farming Tractors

Test Agri Tractor Brakes With BrakeCheck